 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| HMC505LP4 / 505LP4E v01.0805 MMIC VCO w/ BUFFER AMPLIFIER, 6.8 - 7.4 GHz Typical Applications Low noise MMIC VCO w/Buffer Amplifier for: * VSAT & Microwave Radio * Test Equipment & Industrial Controls * Military Features Pout: +11dBm Phase Noise: -106 dBc/Hz @100 kHz No External Resonator Needed Single Supply: +3V @ 80 mA QFN Leadless SMT Package, 16mm2 Functional Diagram General Description The HMC505LP4 & HMC505LP4E are GaAs InGaP Heterojunction Bipolar Transistor (HBT) MMIC VCOs with integrated resonators, negative resistance devices, varactor diodes, and buffer amplifiers. Covering 6.8 to 7.4 GHz, the VCO's phase noise performance is excellent over temperature, shock and vibration due to the oscillator's monolithic structure. Power output is +11 dBm typical from a single supply of +3V @ 80 mA. The voltage controlled oscillator is packaged in a leadless QFN 4x4 mm surface mount package. 15 VCOs - SMT Electrical Specifications, TA = +25 C, Vcc = +3V Parameter Frequency Range Power Output SSB Phase Noise @ 100 kHz Offset, Vtune= +5V @ RF Output Tune Voltage (Vtune) Supply Current (Icc) (Vcc = +3.0V) Tune Port Leakage Current Output Return Loss Harmonics 2nd 3rd Pulling (into a 2.0:1 VSWR) Pushing @ Vtune= +5V Frequency Drift Rate 9 -19 -28 6 20 0.8 1 80 10 8 Min. Typ. 6.8 - 7.4 11 -106 11 Max. Units GHz dBm dBc/Hz V mA A dB dBc dBc MHz pp MHz/V MHz/C 15 - 96 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC505LP4 / 505LP4E v01.0805 MMIC VCO w/ BUFFER AMPLIFIER, 6.8 - 7.4 GHz Frequency vs. Tuning Voltage, T= 25C 8 7.8 7.6 FREQUENCY (GHz) 7.4 7.2 7 6.8 6.6 6.4 6.2 6 0 1 2 3 4 5 6 7 8 9 10 11 TUNING VOLTAGE (VOLTS) 2.75V 3.0V 3.25V Frequency vs. Tuning Voltage, Vcc= +3V 8 7.8 7.6 FREQUENCY (GHz) 7.4 7.2 7 6.8 6.6 6.4 6.2 6 0 1 2 3 4 5 6 7 8 9 10 11 TUNING VOLTAGE (VOLTS) +25C +85C -40C Sensitivity vs. Tuning Voltage, Vcc= +3V 400 360 SENSITIVITY (MHz/VOLT) Output Power vs. Tuning Voltage, Vcc= +3V 18 16 OUTPUT POWER (dBm) 320 280 240 200 160 120 80 40 0 0 1 2 3 4 5 6 +25C +85C -40C 14 12 10 8 6 4 15 +25C +85C -40C 7 8 9 10 11 0 1 2 3 4 5 6 7 8 9 10 11 TUNING VOLTAGE (VOLTS) TUNING VOLTAGE (VOLTS) Phase Noise vs. Tuning Voltage -60 -65 -70 -75 -80 -85 -90 -95 -100 -105 -110 -115 -120 -125 0 1 2 3 4 5 SSB PHASE NOISE (dBc/Hz) Typical SSB Phase Noise @ Vtune= +5V 0 SSB PHASE NOISE (dBc/Hz) -20 -40 -60 -80 -100 -120 -140 -160 3 10 +25C +85C -40C 10kHz offset 100kHz offset 6 7 8 9 10 11 10 4 10 5 10 6 10 7 TUNING VOLTAGE (VOLTS) OFFSET FREQUENCY (Hz) For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 15 - 97 VCOs - SMT HMC505LP4 / 505LP4E v01.0805 MMIC VCO w/ BUFFER AMPLIFIER, 6.8 - 7.4 GHz Absolute Maximum Ratings Vcc Vtune Channel Temperature Continuous Pdiss (T = 85C) (derate 6.31 mW/C above 85C) Thermal Resistance (RTH) (junction to package base) Storage Temperature Operating Temperature +3.5 Vdc 0 to +11V 135 C 315 mW 158 C/W -65 to +150 C -40 to +85 C Typical Supply Current vs. Vcc Vcc (V) 2.75 3.0 3.25 Icc (mA) 70 80 90 Note: VCO will operate over full voltage range shown above. ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS Outline Drawing 15 VCOs - SMT NOTES: 1. LEADFRAME MATERIAL: COPPER ALLOY 2. DIMENSIONS ARE IN INCHES [MILLIMETERS] 3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE. 4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM. PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM. 5. PACKAGE WARP SHALL NOT EXCEED 0.05mm. 6. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND. 7. REFER TO HITTITE APPLICATION NOT FOR SUGGESTED LAND PATTERN. Package Information Part Number HMC505LP4 HMC505LP4E Package Body Material Low Stress Injection Molded Plastic RoHS-compliant Low Stress Injection Molded Plastic Lead Finish Sn/Pb Solder 100% matte Sn MSL Rating MSL1 MSL1 [1] Package Marking [3] H505 XXXX H505 XXXX [2] [1] Max peak reflow temperature of 235 C [2] Max peak reflow temperature of 260 C [3] 4-Digit lot number XXXX 15 - 98 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC505LP4 / 505LP4E v01.0805 MMIC VCO w/ BUFFER AMPLIFIER, 6.8 - 7.4 GHz Pin Descriptions Pin Number 1- 14, 17 - 19, 21, 23, 24 Function N/C Description No Connection. These pins may be connected to RF ground. Performance will not be affected. Interface Schematic 15 GND This pin must be connected to RF & DC ground. 16 RFOUT RF output (AC coupled) 20 Vcc Supply Voltage Vcc= 3V 15 22 VTUNE Control Voltage Input. Modulation port bandwidth dependent on drive source impedance. GND Package bottom has an exposed metal paddle that must be RF & DC grounded. For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 15 - 99 VCOs - SMT HMC505LP4 / 505LP4E v01.0805 MMIC VCO w/ BUFFER AMPLIFIER, 6.8 - 7.4 GHz Evaluation PCB 15 VCOs - SMT List of Materials for Evaluation PCB 105706 [1] Item J1 - J2 J3 - J4 C1 C2 U1 PCB [2] Description PCB Mount SMA RF Connector DC Pin 4.7 F Tantalum Capacitor 10,000 pF Capacitor, 0603 Pkg. HMC505LP4 / HMC505LP4E VCO 105667 Eval Board [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Rogers 4350 The circuit board used in the final application should use RF circuit design techniques. Signal lines should have 50 ohm impedance while the package ground leads and exposed paddle should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request. 15 - 100 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC505LP4 / 505LP4E v01.0805 MMIC VCO w/ BUFFER AMPLIFIER, 6.8 - 7.4 GHz Notes: 15 VCOs - SMT For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 15 - 101 |
Price & Availability of HMC505LP4
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |